(You won't be able to re-calibrate your screen for water resistance, for instance.)But if you'd prefer to repair your gadgets yourself, here's the best way to go about it. How to replace a tempered glass screen protectorIn past years, we've recommended this option above making an appointment with Apple, but as the iPhone screen has gotten more complicated — a home-brew repair can potentially hinder your device from full operability. It also won't maintain your iPhone's water resistance. I'll note that this is a temporary measure, and one I generally recommend for screens that are cracked, but not completely destroyed — it can keep the cracks from worsening or pieces of the screen from falling apart, but eventually, you'll need to replace the screen. Here are a couple, in order of easiest (and cheapest) to most complicated.Cheap Power Tool Sets, Buy Quality Tools Directly from China Suppliers:TBK 808 12 inch Curved Screen Vacuum Laminating and Bubble Removing Machine Laminator and Debubbler For LCD Screen Repairing Enjoy Free Shipping Worldwide Limited Time Sale Easy Return.If your screen is shattered but relatively intact, you can put off a potentially-costly repair by sealing the broken pieces behind a screen protector. There are several ways to repair or replace a broken iPhone screen, depending on your monetary situation and free time.Maintain a clean, organized workspace so you don't lose or confuse any components. Always use good lighting - smart device components are small and you'll need plenty of light to see what you are doing. Hold both buttons down until you see the Apple logo on the screen.If the Apple logo doesn't appear after holding down the buttons and waiting for at least 90 seconds, your phone likely needs a screen repair.Always make sure to back up your phone before any repair. While holding the Power button down, press and hold the Volume Down button on the left side of your phone. Press and hold the Power button on the right side of your phone.
![]() Tool For Removing Lcd Screen From Free Shipping WorldwideAt any point during a repair, if the adhesive becomes hard to separate, apply more heat. Apply enough heat to loosen adhesive but not enough to damage the device. Most screws cannot be interchanged. Turn your iPhone off and heat it up.Start by heating up the device's interior adhesive strips with a dehydrator, heat gun, or heat mat. You're going to be working with some tiny screw here these will help you keep them on your table and not lost on the floor. Or at all.While not required to repair your iPhone, we also recommend you use a magnetic mat and screw capsules to keep everything organized. Required tools and partsNot only will need a new screen — an "LCD Assembly", if you want to be technical about the part — you're going to need some tools if you're going to do this right. In addition, loosening the screen's adhesive requires controlled heating with a dehydrator or heat gun. Open the iPhoneRemove the two pentalobe screws on the bottom edge of the phone. Ten to twenty seconds of a heat gun on a low setting should be all you need to loosen the adhesive. Twenty minutes in the dehydrator should be enough. This is a thin cable that is easy to tear so use caution.The Touch ID sensor must be removed carefully. It is secured by four tri-point screws one of those screws is longer than the others.After the shield is off, use a spudger to disconnect the battery from the logic board.Disconnect the display connector flex cable using the spudger.Unscrew the two Philips head screws on the shield over the front panel sensor assembly connector that's the silver shield near the top of the phone with the flex cable coming out of the bottom.Disconnect the black front panel sensor assembly connector cable from the logic board with the spudger: It's the one that connects the screen to the iPhone's body.Remove the LCD assembly of the iPhone 7 Plus from the body.Next, we will remove the five Phillips head screws that hold the silver bracket on the top of the LCD assembly.Pull the front camera up and out of the way with your spudger or tweezers.You can now also remove the earpiece speaker.Use your spudger to remove the ambient light sensor and proximity sensor. The flex cable connecting the screen to the battery will still be attached, so exercise caution.Remove the silver EMI shield on the mid-right side of the phone needs. Don't push the metal spudger too far into the device.The left side of the screen will open off the body like a book opened from the back cover. Start on the bottom edge by the Lightning port and proceed slowly.Continue using the metal spudger or use playing cards or guitar picks to separate the adhesive from the sides and top. What is the best mac pc emulatorIt needs five Phillips heads.Reconnect the front-facing camera flex to the logic board.Screw in the front facing camera EMI shield using two Philips head screws.Fasten the display flex EMI shield back onto the mid-right side of the phone using its four tri-point screws. The shorter screw goes directly on the home button.Using your plastic spudger, gently press the ambient light and proximity sensor back into place.Attach the bracket over the front camera. Do not overtighten as this can cause home button issues. There are four tri-wing screws. The flex cable passes through an opening on one side.Using your spudger, disconnect the home button cable connector.Disconnect the underlying connection carefully.Pry the adhesive holding the Touch ID and Home button to the back of the digitizer.Push the home button forward through the front of the screen.Insert the home button into the new screen from the front.Pass the flex cable through the LCD shield.Set the LCD shield in place over the screen.Screw the 5 tri-point screws and single Philips head screw that fasten the LCD shield to the screen.Re-attach the home button bracket. There are 5 tri-point screws and 1 Philips head screw on the bottom edge.Pull the LCD shield away from the screen.
0 Comments
Leave a Reply. |
AuthorKevin ArchivesCategories |